Mold Inspection San Leanna TEXAS
- Are you experiencing allergic symptoms, such as stuffy head, headaches, scratchy throat, runny nose and not sure why.
- You think you see mold but are not totally sure it is mold.
- You smell a musty odor but don’t see any obvious mold.
Let Our Experts Assist You 888-887-5257
Mold • What is it?
Mold is a fungus that is found naturally in our environment. While it is found everywhere, it becomes a problem when its spores reproduce inside your home or building. Once it is determined that you have a mold problem, your next step is to get it removed as quickly as possible.
Any Contractor can offer mold inspection, the challenge is finding one who can perform the inspection services without the mold coming back or spreading throughout the home or commercial property.
Mold Inspection | What We Do
If you are unfortunate enough to discover a problem with mold growth in your home be it in the basement, attic or on the wall of your bedrooms or lounge it is imperative that you deal with the problem and immediately. Whilst small spots of mold can be dealt with using DIY methods large areas must be professionally assessed and treated due to the potential health risks involved.
In order to establish the type of mold present and the type of the repairs which will have to be undertaken you will need to have a mold inspection undertaken by a qualified professional. A note of caution: there are numerous mold inspectors out there but it is important that you are not tempted to choose one simply because the cost is minimal. This is a potentially serious situation and you really have to employ the best you can afford.
So, what is a mold inspection all about?
A mold and mildew inspection will certainly determine any kind of conditions around your residential or commercial property which will support mold growth along with determining problem locations as an example water damages, smells and also noticeable indicators of fungal development etc. The mold and mildew examiner should take the examination outdoors and examine the exterior of the house again for obvious indicators of water damage, leakages and also their resources such as damaged pipes, damaged gutters, fractured block work and more.
What does the inspector actually do during a mold inspection?
After the initial visual checks the first job is normally to gauge moisture levels present in the walls of the property. The moisture levels are measured at intervals of about two feet and special attention must paid by the inspector in areas under sinks, around water heaters, anywhere that there is a water source present. Moisture levels are measured using a special meter which has two small pins which are inserted into the lower part of the wall and will give a reading to show the level of moisture present. The acceptable level is 15% or below.
Should at this point in the mold inspection your inspector discovers wall readings greater than the acceptable figure or comes across signs of water damage or mold growth he/she should bring them to your attention and possibly discuss whether samples should be taken. However, even assuming there are visible stains from water damage or perhaps mold growth the inspector will still be unable to give any indication for certain that you have a mold problem which is why sampling is essential.
Mold Inspection San Leanna TX
The sample taken is most likely to be an air sample. By taking air samples during a mold inspection it is possible to establish what strain of mold is present in the atmosphere and in what quantities. I must point out at this stage that the mold inspector has to take at least two air samples. The first should be from the area which is causing concern and the second should from outside. Why take a sample from outside? The answer to this is easy. Mold is found everywhere, we breath it in all the time and for the most part it is 100% safe and does us no harm what so ever. So, during a mold inspection it has to be established whether or not the mold inside is the same strain as that outside and if it is in the same ratio or less. The other side of the coin is obviously that the mold type may be the same but the concentrations much higher inside or it may be toxic mold.
Where there is visible mold growth samples of this can also be taken allowing the precise type of mold spores to be identified, however this will not determine whether or not these mold spores are in the air.
How fast can you expect results?
Generally of thumb, these samples can take 3-4 days to process at the lab but I would certainly expect that your mold and mildew inspector make get in touch with and also give a verbal record as soon as the results become available followed by a composed record within a number of days. An additional indicate know, when it involves the record complying with a mold and mildew evaluation an excellent mold and mildew inspector will certainly not merely send you a copy of the lab record. He/She should able to with confidence translate the results and also supply them along with suggestions to resolve the problem !
NB. Should you reserve a mold and mildew inspection it is important that you maintain doors and windows shut as long as possible for the 12 to 24 hrs previous to the assessors go to. This will enable that the mold and mildew evaluation results are exact. It will permit the mold and mildew examiner to detect odours and air samples will certainly not include excess outdoors air.